silver wholesale jewelry uk What CNC CNC CNC CNC CNC Machine Tool is available for Cartier screw rings and bracelets. Where can I buy it and how much is it?

gold jewelry wholesale atlanta georgia How to make beautiful bracelets with hardware materials? What are the methods and materials for making hardware bracelets? Make beautiful bracelets with hardware materials! This simple bracelet looks very high -end, but it is not expensive at all, and the style is classic and simple.

1 ♥ Tools and materials
If of. Some of them, such as round nose pliers, are mainly special tools for jewelry, and some of them are also sold in hardware stores.
● A pair of anvils or correction platform (a large piece of smooth solid metal)
● Hammer, the surface is very smooth
● Piers, a few layers of tape wrapped in the mouth to ensure the smoothness of its surface)
● Round nasal pliers (the needle is wrapped in the tip of the mouth can also be)
● Glore
● Floral tape
● Metal knife
● Polishing cloth
● Small things sold in the hardware store

01 Volume 20GA Bronze Line
0 One Volume 20GA Copper Line
Volumes Volume 18GA Copper Line

n first cut a 24 -inch 18GA copper thread. Wipe it clean and straighten, and then cut it into a 5 -inch length. In the end, there will be a 4 -inch length.
This with an anvil and a hammer to flatten the 5 -inch length. As far as possible, the better. After knocking, the length will increase by about 1/4 inches and some arc. Just use nylon tongs to twist the arc. Use polishing cloth and knife to polish each copper wire. Then put it aside.
F folding the 4 -inch long copper wire and then tap gently. This one doesn't have to be as flat as others. Put it on the side after polishing the light.

3 ♥ Make the peripheral twist line
This cutting a 18 -inch 20ga copper thread, brass and copper must be. Wipe it clean and straighten, and then twist them together with a needle. Put aside.
4 中 The braid in the middle of the weaving
This is the most complicated step. You need to read a few more times.
The first photo.
This 4 -segment long 10 -inch brass lines and copper lines. Wipe them and straighten them. Tied them to one piece, straight lines, put on a floral tape with one end, and the brass and bronze are separated from each other. It may not be particularly neat, but it doesn't matter. Try to be neat.
It the second photo.
The clip is clamped on the position of the bundled tape. A pair of pairs of ground (a brass, a piece of copper) bent in different directions in different directions. A group of front, one group.
The third photo.
The copper thread on the right bent to the left and span across.
The fourth photo.
This of the remaining three pairs of copper threads bent in the opposite direction and pressed on the cross -crossing copper thread.
The fifth photo.
The copper thread that spans across, that is, the far right at the beginning, and now the right pair of bending parallel parallel to the second pair.
The sixth photo.
The clip is very careful, put the copper thread down, so that they are just on the edge of the clip. In this way, the first layer of braid was sandwiched. Then clip the clip again. Repeat these steps until all copper wires are woven. (Clamp, weaving, letting go, decentralization, clipping, and here again.) If you want to temporarily put down the copper thread on hand to do other things, then write down the front side of the current side, wait for you to re -you again It will not be wrong at the beginning. (If the direction of the weaving is reversed, it is wrong.)
Seventh photo.
When you are weaving, let the copper wire poke out from the right side of the clip. When you can't make it down, you can remove the braid from the clip and pull it straight with a nylon tong. You can also tap with a hammer to flatten the tangled part. Try the end and leave the 6 -inch long copper wire. If necessary, you can polish the end of the copper wire and repair the rough part.
I tried to make the photo look clearer. If you still don't know, you need to explain it in detail, you can look at the "" written, and I basically extract it from it. Many libraries have this book.

5 ♥ Make a sealing sleeve
The copper thread to twist the copper thread of twist and set it on the copper line after weaving.
The fixing them with floral tape.

6 ♥ Bind the sealing cover with the braid
This bend a hook on a 5 -inch flat flat bronze line. Wrap it neatly at the end of the bracelet, fix the weaving copper thread on the twist line, and leave a small ring as a hook. Take 3 or 4 laps, then cut and flatten the back of the flat copper line.
(You want to cut off the flat copper wire about half, but the excess part is indispensable, otherwise it will not be able to grasp it tightly.)
The is handled in another position. On the other side, there is about 1.5 inches between the end of the two. Practice the rough places.
In the flat copper wire around the seal.
7 Complete
The photo of the bottom left and upper right: Tour the copper line of the twist to about 1/2 inch. If necessary, tighten it. Follow them into two rings and plug in the flat copper line at the end. You have to ensure that the flat copper wire will not slide out ...
The upper right photo: the one with a 4 -inch long copper thread bent the one to a hook. At this time, measure the size of the hook ring, and then trim the hook to the appropriate size so that the bracelet can be fits your wrist. When dealing with the copper wire, you must be patient, so that the end of the hook will not be tied to the hand -the distance is very close when it is close.
Photo on the bottom left: Connect the hook on the Twist copper line. The two ends are made into the two rings made in this step, and then roll the end inside the bracelet (like a scroll).
Background photos: Find something that can be used as a round heart axis from the tools on hand, and carefully bent the bracelet into the shape of the wrist. I use a PVC plastic tube to tighten the curve on the side, and then I can easily put my hands into this curve. For some reasons, round shapes are actually not good. When you hold the hook, you can try to pull the short side and let the two sides symmetrical.
8. Appreciate your work
Since you have spent two or three hours to make this bracelet, you should sit comfortably and enjoy your handmade works. You can also take some photos (you can use small stones as a background or choose what you like).
Then you can do one more, I guess you are probably reluctant to give the first one!
It to keep the brilliance of the brass, you can apply some dry baking soda, then wipe it with an old and dry toothbrush, and then rinse with water and dry it. The method of brushing with a toothbrush is just like when you brush your teeth, you can flash your bracelets.